VERSION HISTORY v15.0 --------------------------------------------------------------------- - now miner supports up to #384 epoch (4GB DAG size). Note that previous versions support up to #299 epoch, you will not be able to use old versions after #299 epoch. - added support for Navi cards (ETH-only mode). - now miner sets environment variables automatically (required for 4GB AMD cards). v14.7 --------------------------------------------------------------------- - now the miner driver does not require switching Windows to Test Mode. If you want to turn Test Mode off, use "-driver uninstall" option (with admin rights) and reboot, then start miner with admin rights to install new driver automatically when necessary (or use "-driver install" option directly). If you have any problems with signed driver you can use "-driver install_test" option, it uses old approach: enables Test Mode (reboot is required) and installs unsigned driver. - added "-showpower" option for stats about GPU power consumption, press "s" to see it. Both AMD and Nvidia cards are supported, except Linux gpu-pro drivers and Radeon7 cards. - updated Remote Manager to show total power consumption. - fixed issue with "-logsmaxsize" option when "-logfile" option is used to specify directory for log files. - a few minor bug fixes and improvements. v14.6 --------------------------------------------------------------------- - now "-rxboost" option also supports old AMD cards (Hawaii, Tonga, Tahiti, Pitcairn), use "-rxboost 1" to improve hashrate up to 5% by applying some additional memory timings. - now "-rxboost" option supports all AMD drivers. - now "-strap" for AMD cards also supports AMD blockchain drivers. - some changes to further reduce stale shares a bit. - added "-minspeedtime" option. - added statistics for shares accepting time (min/max/average), press "s" to see it. - updated Remote Manager to show shares accepting time. - Linux version build with some performance improvements. - a few minor bug fixes and improvements. v14.5 --------------------------------------------------------------------- - added "-rxboost" option for AMD Polaris cards, use "-rxboost 1" to improve hashrate by about 5% by applying some additional memory timings. You can use your own straps or use "-strap" option, you will get boost anyway. See Readme for additional information. - fixed issue with overclock reset for Nvidia cards. v14.4 --------------------------------------------------------------------- - improved mining speed for Nvidia cards by about 1% (depends on card model). Note that dual mining for Nvidia cards suffers from this optimization, use old versions if you use dual mining on Nvidia cards. - a bit reduced intensity of all Nvidia straps. - added "-sintensity" option to adjust strap intensity for Nvidia cards, see Readme for details. v14.3 --------------------------------------------------------------------- - fixed BSOD issue with Vega cards. - improved handling memory timings for Nvidia. - "strap" option for Nvidia cards: added "-strap 4"..."-strap 6" options, they have less intensity than straps #1..3 so you can try to use them if you cannot use even "-strap 1" option. v14.2 --------------------------------------------------------------------- - "strap" option: added support for Nvidia 10xx cards, up to 10% speedup for 1050/1060/1070 cards, up to 50% speedup for 1080/1080Ti cards compared to stock BIOS. Use "-strap 1" ... "-strap 3" values and overclock memory to find the best hashrate. - a few minor bug fixes and improvements. v14.1 --------------------------------------------------------------------- - "strap" option: added support for Vega cards, up to 15% speedup compared to stock BIOS. Use "-strap 1" ... "-strap 5" values and overclock memory to find the best hashrate. - improved compatibility with AMD 18.x drivers. - now miner uses CUDA10 runtime library for Nvidia. - a few minor bug fixes and improvements. v14.0 --------------------------------------------------------------------- - Windows only: added ability to apply optimized memory timings (straps) on-the-fly, without flashing VBIOS, up to 25% speedup compared to stock BIOS. Currently only Polaris cards are supported, other cards will be added later. Drivers 18.x or newer are required. Best straps for Ethereum are included. Check "-strap" and "-driver" options for details. - Windows only: added temperature/fan/clocks management for Radeon VII. - a few minor bug fixes and improvements. - fixed fan control for latest Windows AMD drivers. v12.0 --------------------------------------------------------------------- - zero devfee for all 2GB and 3GB cards in all operating systems. - reduced devfee for dual mode, now it is 1%, same as for ETH-only mode. - a bit reduced required GPU memory (both AMD and NVIDIA) so you can mine ETH a bit longer on cards that don't have enough memory. - added version for CUDA 10.0, it is a bit faster for latest 20xx NVIDIA cards. - a few minor bug fixes and improvements. v11.9 --------------------------------------------------------------------- - fixed issue with incorrect shares for Keccak. v11.8 --------------------------------------------------------------------- - fixed issue with missed GPU temperatures when miner is started via Remote Desktop Connection (RDC). - Linux version: removed libcurl library dependency. - added "-showdiff" option. - a few minor bug fixes and improvements. v11.7 --------------------------------------------------------------------- - added temperature management and overclock support for recent Nvidia cards in Windows: "-tt", "-powlim", "-cclock", "-mclock", "-tt", "-fanmax", "-fanmin" options are supported for Nvidia too. - now "y" key also disables CrossFire. - added "-y" option. - fixed issue with miner restart that was required sometimes to apply overclock settings for AMD cards. - fixed issue with rejected shares when "-esm 3" option is used. - Linux version: fixed issue with remote management. - some changes in watchdog routines to improve ability to restart miner after various OpenCL fails. - a few minor bug fixes and improvements. v11.6 --------------------------------------------------------------------- - improved hashrate for weak Nvidia cards by about 1%. - zero devfee for 3GB cards in Windows 10, same as for all 2GB cards. - applied some tricks to increase available memory for 3GB cards in Windows 10 so you can mine ETH a bit longer. - now you can press "y" key to turn on "Compute Mode" in AMD drivers for all cards (Windows only). - Linux version: removed openssl library dependency. - improved "-logfile" option, now you can use it to specify a folder for log files, use slash at the end to do it, for example, "-logfile logs\". - added "-epoolsfile" and "-dpoolsfile" options. - remote management: now "miner_getstat2" command also returns PCI bus index for every GPU. - a few minor bug fixes and improvements. v11.5 --------------------------------------------------------------------- - added "-oldkernels" option (AMD GPUs only), you can try "-oldkernels 1" to use old-style GPU kernels from v10, they can be more stable for hard OC and custom BIOSes. - a bit reduced stale shares for Nvidia GPUs. v11.4 --------------------------------------------------------------------- - fixed issue with stale shares. - fixed issue with incorrect shares. - a few minor bug fixes and improvements. v11.3 --------------------------------------------------------------------- - added automatic detection of best -dcri values in ASM ETH-only mode if -dcri option is missed. Press "s" key to see current values, you can also press "z" key to restart detection. - improved support for systems with many GPUs (eight and more) and slow CPU: much less CPU load, EthMan works fine now. - added assembler kernel for RX550 card. This card is not good for dual mining, but in ETH-only mode ASM kernel is faster by about 7%. - added "x" key to select GPU for manual -dcri value adjustment. - several minor bug fixes and improvements. v11.2 --------------------------------------------------------------------- - some improvements in AMD GPU kernels, it can increase hashrate a bit in some cases. - reduced some delays, it will cause a bit less stale shares. v11.1 --------------------------------------------------------------------- - added SSL support with pool certificate verification, it significantly improves security, use "ssl://" prefix for pools that support SSL encryption. - added "-checkcert" option. - EthMan updated. v11.0 --------------------------------------------------------------------- - added new algorithm for dual mode: blake2s (stratum pools only), use "-dcoin blake2s" option. - added new algorithm for dual mode: keccak (stratum pools only), use "-dcoin keccak" option. - reduced devfee for dual mode, now it is 1.5%. - for 2GB cards devfee is removed completely, i.e. on 2GB cards you can mine all ETH forks without devfee. Check Readme for details. - added "-tstart" option. - "-asm 2" option value now supports Tahiti, Tonga, Ellesmere, Baffin; in some cases it can be a bit faster in ETH-only mode. - removed "-allcoins exp" option value. - a few minor bug fixes and improvements. v10.6 --------------------------------------------------------------------- - fixed critical issue in remote management feature (attacker could crash miner even in read-only mode). v10.5 --------------------------------------------------------------------- - applied another workaround for ADL, you must not see "Temperature control thread hangs" message now. - added version for CUDA 9.1. - now miner shows a warning if you enabled full remote management (-mport > 0) and did not specify -mpsw parameter. - now miner shows a warning if you specified default ETH wallet (from default start.bat). v10.4 --------------------------------------------------------------------- - fixed issue with rejected shares in ETH+SIA mode for Vega cards. - improved watchdog for temperature/fan management thread. v10.3 --------------------------------------------------------------------- - added support for Adrenalin drivers (GPU sorting, fan/temperature/clocks management). - fixed issue with possible GPU crash during miner shutdown. - now miner shows PCI bus number for every GPU. - a few minor improvements. - EthMan: some bug fixes and minor improvements. v10.2 --------------------------------------------------------------------- - fixed critical issues in remote management feature (attacker could crash miner even in read-only mode). - now miner supports up to #299 epoch. - in rare cases ADL API calls can hang, now watchdog checks it as well. - improved "-minspeed" option, check readme for details. - added "miner_getstat2" command to remote management, check "API.txt" for details. - EthMan: added detailed stats mode in main window. v10.1 --------------------------------------------------------------------- - now if miner has to recreate DAG for devfee, new DAG generation time will be included in devfee time. - improved "-gser" option, now you can set custom delay between DAG generation on GPUs, check Readme for details. - added detailed stats about rejected shares per GPU ("s" key). - added "-logsmaxsize" option. - fixed issues with "-r -1" option value. - EthMan: added detailed stats mode in web server. - a few minor bug fixes and improvements. v10.0 --------------------------------------------------------------------- - added assembler kernels for ETH+LBC mining mode (AMD cards only), major speedup for LBC. - about 1% ETH speedup for Vega cards. - fixed issues with voltage/clocks management for latest AMD blockchain drivers (not completely). - new GPU sorting method for NVIDIA cards. Now GPUs are sorted by physical bus index (it matches AfterBurner list of GPUs). - for ETH+LBC mining mode maximal "dcri" value is 1000 now. - added "-platform" option. - added "ESTALE" option support in failover file epools.txt (see "-estale" option for details). - several minor bug fixes and improvements. v9.8 --------------------------------------------------------------------- - added Vega cards support (ASM mode). - added fan/OC support for 17.7.2 (and higher) drivers. - fixed issue with -ttli and -ttdcr option for Nvidia cards. - improved support for systems with more than 10 GPUs, check readme for "-di" and "-mode" options description for details. - a few minor bug fixes and improvements. v9.7 --------------------------------------------------------------------- - Added ASM mode for RX460/560 cards, up to 30% speedup for second coin in dual mode. - Improved ETH speed for some Nvidia cards. - Improved speed in dual mode for Nvidia cards. - reduced initialization time. - a few minor bug fixes and improvements. - EthMan: added ability to select several rigs. - EthMan: several minor bug fixes and improvements. v9.6 --------------------------------------------------------------------- - new GPU sorting method for AMD cards. Now GPUs are sorted by physical bus index (it matches AfterBurner list of GPUs). Also the list of temperatures/fans matches the list of GPUs automatically. Therefore "-di detect" and "-gmap" options are not necessary and not supported anymore. WARNING: be careful if you use use separate overclock/temperature settings for every card, due to new sorting method GPUs can get different indexes! - added "-minspeed" option to restart miner/system if miner cannot reach specified speed. - now watchdog monitors initialization steps too, e.g. it will restart miner even if miner hangs at GPUs initialization. - added "-allcoins etc" option for ETC pools that require Username.Worker, in this mode devfee will be mined on some default ETC pools and DAG will not be recreated. - added current DAG size info when "s" key is pressed. - added 1 minute average speed for ETH when "s" key is pressed. - fixed connection timeout issue in Linux version. - fixed some issues related to remote management via TCP/IP. - added "-ejobtimeout" and "-djobtimeout" options. - fixed epoch #0 support. - a few minor bug fixes and improvements. - EthMan: fixed issue with lost connection to some rigs. - EthMan: added password for webserver. - EthMan: added separate settings for every event. - EthMan: added "retrigger" option for lost connection event. v9.5 --------------------------------------------------------------------- - fixed issue with PASC, miner could check some nonces twice. Effective hashrate must be a bit higher now. - improved SIA support for Nicehash, added "mining.extranonce.subscribe" and "client.reconnect" commands support. Effective hashrate must be a bit higher now. - a few minor bug fixes and improvements. - EthMan: added ability to enable/disable GPUs remotely (see API.txt for tech details). - EthMan: added notification for too high fan speed. - EthMan: several minor bug fixes and improvements. v9.4 --------------------------------------------------------------------- - added alternative Sia Stratum support (Siamining, Nicehash). Stratum version detection is automatic. - improved fans management for latest drivers and Polaris cards. - added "-mpsw" option. - added shares-per-GPU statistics when "s" key is pressed. - Included EthMan v3.0 which supports passwords and email notifications. v9.3 --------------------------------------------------------------------- - improved dual mining speed stability in ASM mode. - added "-altnum" option for alternative GPU indexing. - a few minor bug fixes and improvements. v9.2 --------------------------------------------------------------------- - improved mining speed stability. - added changes in DCR mining protocol. - fixed possible issue with rejected DCR shares on Nicehash pool. - added pool selection in runtime ("e" and "d" keys). - now if devfee mining fails for a long time, miner will not stop mining, it will turn on "-nofee" option temporarily with appropriate warnings, until successful devfee mining. - some minor improvements. - EthMan: added ReasonID parameter to .bat file which is executed when some rig has problems, check "sample.bat" for details. v9.1 --------------------------------------------------------------------- - added assembler kernels for ETH+SIA and ETH+PASCAL modes (major speedup for SIA and PASCAL). - added alternative assembler kernels for Tonga and Polaris cards for ETH-only mode. Use them if you get best speed at "-dcri 1" (i.e. you cannot find speed peak), use "-asm 2" option to enable this mode. - a few minor bug fixes and improvements. v9.0 --------------------------------------------------------------------- - added "-asm" option (AMD cards only) which enables assembler GPU kernels. In this mode some tuning is required even in ETH-only mode, use "-dcri" option or or "+/-" keys in runtime to set best speed. Currently only ETH-only and ETH-DCR modes are supported in assembler. Use "-asm 0" if you don't want to use new assembler kernels. If ASM mode is enabled, miner must show "GPU #x: algorithm ASM" at startup. - improved ETH mining speed in ASM mode for some cards, also a bit reduced power usage for some cards (fine-tuning is required via "-dcri" or "+/-" keys in runtime). NOTE 1: if GPU throttles, best "-dcri" value is different. NOTE 2: speed peak can be rather short, so change "-dcri" value slowly. - dramatically increased DCR mining speed in assembler mode (up to 70%). Be careful, power usage is higher too. - added "-gmap" option. - fixed DCR Nicehash support. - added "FINE-TUNING" section to Readme file. - A lot of minor improvements and bug fixes. v8.1 --------------------------------------------------------------------- - added Ethereum+Pascal mode for NVidia cards. - improved "-di detect" option: now after GPU order detection miner starts mining with the detected order. - now remote management is working in read-only mode by default. - improved "-mport" option, now you can specify network adapter IP for incoming connections for remote management. - added "-benchmark" option. - fixed issue with "-retrydelay" option. - added "-v" option. - a few minor bug fixes and improvements. - EthMan: added option for font color selection. v8.0 --------------------------------------------------------------------- - added new coin for dual mode: PASCAL(PASC). Now you can mine Ethereum, Ethereum+Decred, Ethereum+Siacoin, Ethereum+Lbry or Ethereum+Pascal. NOTE: Currently Pascal is not available for NVidia cards. - added "-nofee" option. - added ability to use environment variables in "epools.txt", "dpools.txt" and "config.txt" files. For example, define "WORKER" environment variable and use it as "%WORKER%" in config.txt. - added "License.txt" file. - some minor improvements. v7.4. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - added "-retrydelay" option. - EthMan: added "View miner console" command. v7.3. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - now miner supports HTTP for remote monitoring, you can check miner state remotely via browser, check "-mport" option for details. - added temperature management for Linux gpu-pro drivers. Note: root access is required to manage fans speed. - added "-fanmin" option. - fixed issue with "-allcoins exp" option. - EthMan: added options for number of decimal points in displayed statistics. - some minor improvements and bug fixes. v7.2 --------------------------------------------------------------------- - added "-lidag" option to reduce intensity of DAG generation, it can help with OC or weak PSU. - added temperature/fan monitoring for Linux version for gpu-pro drivers. Only monitoring is supported currently, not management. - "r" key reloads pools from epools.txt and dpools.txt in runtime. - fixed issue with wrong detection of card names. - systems with up to 32 GPUs are supported now (with some minor limitations). - Linux version: fixed issue with closing miner with "Ctrl-C". - several minor improvements and bug fixes. - EthMan: added "total online miners" and "total working gpus" info. - EthMan: added color and font size options for the list of miners. v7.1. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - now "-etha 2" is set automatically for Linux and 4xx cards. You can change it by specifying "-etha" directly if necessary. - if miner manages fans, it returns management back to drivers at closing. - added text coloring in Linux version. You can use "-colors 0" option to disable it if necessary. - several minor improvements and bug fixes. - EthMan: added ability to start .bat file if miner has problems. - EthMan: added support for CryptoNote miner. v7.0 --------------------------------------------------------------------- - added new coin for dual mode: LBRY(LBC). Now you can mine Ethereum, Ethereum+Decred, Ethereum+Siacoin or Ethereum+Lbry. - some minor improvements and bug fixes. v6.4 --------------------------------------------------------------------- - added "-etha 2" option value for gpu-pro Linux drivers. - fixed issue with a bit lower mining speed of previous version (AMD cards). - Improved speed by about 3% for NVIDIA 10xx cards in Windows 10 (CUDA 8.0 build). - NVIDIA: added build with CUDA 8.0, it is default now, there are also CUDA 6.5 and 7.5 builds in separate folders. - NVIDIA: added temperatures/fans monitoring. Note that fans management is not available, only monitoring is possible. - EthMan now shows "off" or "stopped" status for disabled/stopped cards in detailed hashrate stats. v6.3. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - added support for NVIDIA 10xx cards in Linux. - fixed issue with gpu-pro drivers in Linux. - minor improvements in OpenCL kernels. - bug fixes. v6.2 --------------------------------------------------------------------- - released version for Linux with nvidia support. - fixed Ethereum solo mining mode. - added "-cvddc" and "-mvddc" options for adjusting voltages for latest AMD 4xx cards. - now you can turn on/off cards in runtime with "0"..."9" keys. - bug fixes. v6.1 --------------------------------------------------------------------- - fixed issue with high CPU load for NVIDIA cards. - NVIDIA: now two builds are available: for CUDA 7.5 and for CUDA 6.5. - fixed issue with resetting WattMan settings. v6.0 --------------------------------------------------------------------- - added nVidia support. Tested on 970, 980 and 1070 cards, both single and dual modes are supported. Mixed AMD+nVidia cards are supported too. - added temperature management for latest AMD 4xx cards. - added "-ttli" option. - fixed possible issues with fan management when "-di detect" is used. v5.3 --------------------------------------------------------------------- - added "-di detect" option value to detect correct GPU order for temperatures management. - improved Nicehash pool support (mining.extranonce.subscribe). - fixed issue with sending config.txt to EthMan. - fixed issue in EthMan (possible garbage during remote editing config.txt). v5.2 --------------------------------------------------------------------- - added Stratum for Siacoin. Currently not all Stratum versions are supported, check help page of your pool for details. - bug fixes. v5.1 --------------------------------------------------------------------- - fixed issue with crash in Ethereum solo mode. - fixed issue in Linux version when http server does not respond. - increased timeout to detect bad pool state when no jobs are received for a long time. - added FAQ section to readme. v5.0 --------------------------------------------------------------------- - added new coin for dual mode: Siacoin. Now you can mine Ethereum, Ethereum+Decred or Ethereum+Siacoin. - added "-dcoin" option to select a coin for dual mode. - added "-allcoins exp" option value that allows you to mine Expanse and don't recreate DAG for devfee mining. - added Decred support for Nicehash pool. - default "-dcrt" option value is "5" now. - improved detection of bad pool state: miner will disconnect if pool rejected more than a half of last 10 shares. - "s" key: now miner also shows current difficulty so you can calculate how long it will take to find a share or a block. - bug fixes. v4.7. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - improved stability of Linux version. - fixed issue with possible crash if pool sends several jobs at once. - added "-li" option. - bug fixes. - EthMan: added more options for sound notification. - EthMan: added option to adjust hashrate warning threshold. v4.6 --------------------------------------------------------------------- - added "-esm 3" option value to support Nicehash Stratum implementation. - added "-ttdcr" option. - improved "-tstop" option - now you can specify negative values to close miner instead of stopping GPU. - added "-fanmax" option. - failover if pool rejects too many shares. - fixed issue with wrong "-esm" value that miner could show. - bug fixes. - EthMan: added sound notification. v4.5. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - improved "-tstop" option - if it turned off wrong card (see "KNOWN ISSUES" section in readme about possible GPU order issue), it will close miner in 30 seconds. - added more statistics for "s" key. - added "-logfile" option. - fixed issue with "-mclock" and "-cclock" options for some cards. - a few minor improvements. - bug fixes. - EthMan: added more info - number of restarts, number of failovers, number of invalid shares. - EthMan: added option to display detailed statistics about GPU hashrates. - EthMan: added command "Execute reboot.bat". - EthMan: added command "Edit config.txt". - EthMan: added "GPU warning temperature" option. - EthMan: if some table columns are hidden, webserver won't show them too. v4.4 --------------------------------------------------------------------- - "-tstop" option now stops mining on overheated GPU instead of closing miner. - if GPU fan is not available (non-standard cooling), miner still shows temperature. - now miner sends also worker name (if specified) when sends current hashrate to pool. - now you can specify configuration file name in the command line. - improved failover files parsing, now commas can be used as parameter values. - Fixed issues with remote control after miner restarting in Linux version. - Linux version, "-r 1" option: if "reboot.bash" not found, miner will execute "reboot.sh". - EthMan: sending epools.txt and dpools.txt - they are applied in the miner immediately now. - EthMan shows the percentage of rejected shares. - EthMan: added "Comments" field in miner properties. - EthMan: added table header and auto-refresh for web page. - EthMan: added warning if some miners in table are red. - EthMan: added ability to minimize to system tray. - bug fixes. v4.3 --------------------------------------------------------------------- - added "EthMan" - an utility for remote monitoring/management. - added "-estale" option to send stale shares for Ethereum, it can increase effective hashrate a bit. - now all options can be stored in "config.txt" file. - added "-ftime" option. - added "-erate" option. - added "-tstop" option. - now miner sends hashrate to geth in solo mining mode. - added "-mport" option for remote management. - bug fixes. v4.2 --------------------------------------------------------------------- - added support for Ethereum solo mining. - added "-gser" option. - added "-eres" option. - added "-powlim" option. - added "-etht" option. - "-tt 1" (default) now does not manage fans but shows GPU temperature and fan status. - added support for "client.reconnect" stratum command for Decred. v4.1. This version is assumed to be stable, so it is not marked as "beta". --------------------------------------------------------------------- - UPDATE: Added build for Linux x64 (tested on Ubuntu 12.04). - improved working with DAG on GPUs during epoch changing, it must work fine now. - added watchdog for threads that communicate with pools. - minor bug fixes. v4.0 --------------------------------------------------------------------- - no DAG files anymore. - removed "-dir" option. - Bug fixes. v3.3 --------------------------------------------------------------------- - failover for both Ethereum and Decred. - added CRC check for DAG files. Now if DAG file is corrupted, miner will detect it and re-create DAG. Don't remove DAG files manually if you think that they can be corrupted - miner will do it automatically if necessary. - default value for "-ethi" option is "8" now (instead of "16"), it slightly reduces delays when miner accepts new job. - Bug fixes, a few minor improvements. v3.2 --------------------------------------------------------------------- - reduced number of rejected shares for Decred-Stratum. - miner sends its current hashrate to pool, some pools have "reported hashrate" column and you can see miner hashrate there. - miner shows how long it takes pool to accept share. - option "-r 1" closes miner and calls "reboot.bat" if some GPU failed, so you can create "reboot.bat" to perform any actions. - Bug fixes, a few minor improvements. v3.1 --------------------------------------------------------------------- - reduced delays at shares sending, it must improve speed on pools a bit. v3.0 --------------------------------------------------------------------- - improved Ethereum mining speed by 1-15% (depends on mining mode and card model, slower card - more speed improvement). - added "-etha" option to select Ethereum algorithm optimized for your cards. - added "-allcoins" option to support Ethereum forks mining. - miner checks all Ethereum shares before sending them to the pool. You will be warned if some GPU finds invalid share, usually due to overclocking. - miner disconnects from the pool if there are not any new jobs for a long time. - "-tt" option now can set target temperature for every card individually. - "-tt" option now can set static fan speeds. - fixed issue with -cclock and -mclock options. However, AMD blocked underclocking for some reason, you can overclock only. - option "-wd 1" is set by default now. - option "-ethi" for values less than "4" now sets very low GPU load to avoid any freezes in Windows. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually. You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" value that is used in official miner. - Bug fixes. v2.0 --------------------------------------------------------------------- - Added Stratum support for Decred. - Added "-esm 2" option for "miner-proxy" Stratum version - for such pools like coinotron, coinmine, etc. - Default "-dbg" value is "0" now, log file is created by default. You can disable it with "-dbg -1" option. - If GPU thread hangs and its speed is not updated, miner shows zero speed for that card. - Added "-wd" option. - Added "-r" option. - Additional checks related to DAG files: checking disc space, removing invalid DAG files. - Bug fixes. v1.2 --------------------------------------------------------------------- - Added "-ethi" option. - Added coloring. - "-mode" option now can be set for every card individually. - "-dcri" option now can be set for every card individually. - Added "-allpools" option. v1.1 --------------------------------------------------------------------- Fixed issue with rejected shares for dwarfpool (and for other pools that use similar code). Fixed issue with f2pool pool. Added "-eworker" option. "-dcri" option: max value is 500 now. Added "Rejected shares" info. v1.0 --------------------------------------------------------------------- - First version.